Here we provide some of the signs and symptoms to look out for when diagnosing faults and problems with the exhaust. Loud, Sporty Sound When Accelerating To inspect the exhaust system effectively, you’ll need to get underneath the car — something easier said than done for DIY car enthusiasts without a lift or a pit at hand. It is possible to buy specialist ramps that allow you to raise the car enough to get under and inspect the exhaust system; just make sure the ones you buy are suitable for the weight of your vehicle. Our exhaust repair putty is safe to use on most cars and exhaust materials. It can be applied to all areas of an exhaust, including straight and curved pipe and box assemblies, and its heat resistance means it will continue to work as normal even when the exhaust gets hot.

Sound is also an issue you need to think about if you’re in two minds whether to get your exhaust fixed. If your exhaust is ‘blowing’, there’s a chance it might be louder than the legal noise limit allowed in built-up areas, meaning you could be fined by the police. With the mixer running on low, slowly sprinkle in tylose powder until fully incorporated. Increase speed to medium and mix for 1 to 2 minutes, until the gum paste has formed a ball around the paddle attachment. Step 1– Wait for your car to cool down and then locate the hole or damage, and clear any debris from the area. Step 3– Wearing protective gloves, apply a thin layer of Gun Gum Paste to the damaged area, either with your finger or the spatula. Apply the bandage and tightly secure it in place.Fondant and gum paste are both made by adding sugar to liquid; however, there are two ingredients that make fondant and gum paste vastly different. Fondant usually contains some type of gelatin, which helps give it that elasticity and pliability. Gum paste, on the other hand, uses Gum-Tex powder for added stability and strength. A small amount of Gum-Tex can also be kneaded into fondant to make it act similarly to gum paste. Is it better to use corn starch or confectioners’ sugar when rolling out fondant or gum paste?

Add powdered sugar, mixing on low until ingredients are incorporated. Increase speed to high and mix for approximately 10 minutes until the mixture forms soft, glossy peaks. Scrape down the sides of the bowl and the paddle, then mix for an additional minute. Holes in your exhaust system might seem like a small problem at first, but they’re the kind of thing that can build up and cause a big headache if left unfixed. Yes – when used with the suitable Gun Gum Repair Bandage. Our exhaust repair paste acts as a durable glue that affixes the repair accessory in place, providing a gas-tight seal. We would always recommend using the putty with the right repair bandage to guarantee the best results and a permanent repair. Does exhaust putty work?Assembling your own exhaust can save you money and help you fix problems with noise or leaking exhaust gases. Your engine will work more efficiently, and it can be done at home in minutes. And with the help of Holts Firegum, you’ll get a permanent fit that’s every bit as reliable as a professional repair. The Holts Gun Gum Putty provides a gas tight seal on your exhaust, permanently repairing small holes and leaks in silencers and exhaust systems. Gun Gum is a leading car exhaust repair putty which has been trusted by car lovers for decades. It creates a gas tight seal, and permanent repair is guaranteed, giving you peace of mind that your exhaust is working as it should. You simply press and smooth the paste over the hole or damaged area and leave it to dry, making it an easy DIY solution for home exhaust repairs. Firstly, select the right accessory for your problem (see our handy guide below). Follow the instructions for the accessory and use with Gun Gum Paste to create a permanent gas-tight seal.

This is a professional quality product providing a permanent solution that resists heat and vibrations. Holts Gun Gum Exhaust Paste is a repair putty that provides a flexible, permanent way to repair a car exhaust. Used with the Gun Gum Exhaust Repair system, the putty adheres to both the exhaust material and the repair bandage, forming a gas-tight seal that hardens as it dries to provide a durable, permanent repair.Do you need to replace part or all of your exhaust assembly? While you could take your car to a garage, replacing exhaust components is something you can do at home with the right tools and knowledge – and this will work out much more affordable than a professional repair. Apply more Gun Gum Paste – seal the edges of the repair bandage with the remaining Gun Gum Paste, ensuring that all exposed edges are covered. Having your exhaust repaired professionally can be expensive but can also be time consuming. Fixing it at home yourself will save you time and money, and using Gun Gum will guarantee that it meets MOT standards. For small projects that require precision, like attaching eyes to a figurine, a little dab of water will work just fine! What are the best tools for working with fondant and gum paste?

Using Holts Exhaust Repair Paste is easy. The tub comes with an application spatula to make it easy to apply the putty exactly where you need it. While it’s possible to diagnose a number of exhaust problems based on different engine sounds, a visual inspection of the exhaust is much more reliable way of assessing the condition of the entire system — from the manifold to the tailpipe. The Holts Gun Gum range is trusted by professionals and DIYers alike as one of the best exhaust repair systems on the market. If you’re looking for advice on how to get the best results when using Holts Gun Gum Exhaust Paste, our FAQs provide some useful tips and insights. What is exhaust putty? Drying times vary depending on the conditions, but you can also run the engine to help speed up the time it takes for the putty to harden. Once it’s dry, you’ll have a solid, permanent repair that guarantees no leaks. Is exhaust putty safe to use?Do not store fondant or gum paste in the refrigerator, as this will cause them to harden and become unusable. Leave overnight to harden or run the engine slowly to speed up drying time – you need to leave the Paste to harden before you continue using your car. Avoid racing the engine, as this could hamper the drying process.