Joined in 2023 
82 
63 About this deal
It is important to remember not to use any harsh chemicals such as chemical detergents, bleach, abrasive fluid, etc. Most exterior doors come with a built-in drainage system, using slots and holes in the bottom of the door’s threshold to ensure excess water runs off and stays outside your home.
After everything has dried sufficiently, re-install the door handles, letter boxes, and any other furnishings. Martin Lewis: What the Autumn Statement means for you – including wages, benefits, pensions, ISAs, housing, national insurance and more Use a brush or a cloth to liberally apply Polytrol. If you notice that some bits are looking shiny and others are looking matt, move any of the surplus oil over to the matt areas. Leave it to work then wipe off the excess Autumn Statement: Workers to pay less in national insurance – but rate cuts don't offset the freezing of personal tax thresholds Applying the Polytrol to a wet surface will not produce the desired effect and could negatively impact the door.
What Are the Benefits of a Composite Door?
Although we didn’t have any mildew on the door, if you do, don’t worry. Mildew can be treated with a 50:50 bleach and water solution. Just scrub it on, leave it for 10-15 minutes, then rinse it off. You'll then need to spend some time sanding the surface of the door so that the paint adheres properly. Once you've sanded it you'll need to wipe it down to get rid of any dust. Buy your door from EYG and you don’t have to worry about a thing – thanks to our ten-year ‘repair or replace’ warranty promise. Clean the surface with Net-Trol, rinse thoroughly and allow it to dry for a minimum of 24 hours depending on the surface. Using Polytrol on metal
Once the door has completely dried (which should take approximately 24 hours), you can apply the oils you need to lubricate the door’s metal parts.
To keep your door looking shiny and new, you should give it a good scrub every few months with soapy water and a microfiber cloth. Be sure to rinse the door afterwards and dry it completely to avoid any water spots.
Rather than repainting the whole thing and making a mess, you could invest in a touch-up pen to fill in those grooves and scratches in the door. You can choose beeswax or a similar product as a finishing touch, which will provide your newly painted door with a protective layer and ensure that the colour will stay beautiful for a long time. For the final step, you should use beeswax or another similar product to give your newly painted door a protective layer for the materials and a professional finish. A heavily scratched front door can hurt the entire aesthetic of your home. It can make the entrance to your house look tired and in need of repair.
You then need to sand down the door all over as that will further help the paint to adhere. After you have sanded it, you then need to give it a thorough wipe down to remove the dust. Painting Before getting starting with Polytrol, make sure that your door is completely dry. Time to get going… This will help to make sure you remove all dirt, grime, oil and any other residue that may make it harder for the paint to adhere to the surface.
Simple to apply using a cloth or soft brush, it’s ready to wipe off in just 10 minutes! It can be used on both horizontal and vertical surfaces and can even be used on fibreglass (GRP). Polytrol dries to a tough and long-lasting flexible finish which does not leave a film – so it won’t peel or flake. The warm, soapy water can now be used on the frame of the door. Be sure to open the door to get all around the edges of the frames and get any of that concealed dirt that may affect the closing of your door if allowed to build up. Once the paint is applied, you'll need to add a layer of beeswax or another product to protect the paint. This will also give it an attractive finish. You can use Dilunett to remove the previous orange-brown coating, however, Dilunett is powerful enough to remove up to 8 coats of paint in one application, so any other coats of paint that lay underneath the new paint will also be removed.
Visit the Door Designer
Good preparation is key to a good finish. To have an excellent result you must begin with a clean door free to any dirt, grease, grime and mildew. As Polytrol work by saturating deep down into the surface, if you have any wax or polish applied to the door, this will also need to be removed before application of Polytrol can begin. Remove any door furniture, such as handles or letter boxes, and apply masking tape around any glass windows as well as the door frame. Once you have finished using Polytrol, clean any brushes or other tools you may have used with white spirit. Cloths can be left flat to airdry before discarding. Martin Lewis: What the Autumn Statement means for you – including wages, benefits, pensions, ISAs, national insurance and more
Great Deal 
New Comment