Joined in 2023 
82 
63 About this deal
The first number is the largest diameter measurement of the thread. For example, a 4-30 x 0.10 has a diameter of 0.112 inches. It is because 0.060 + (4 x 0.013) = 0.112 inches. Should you see the letter M, it means the measurement is in millimeters. For example, M5-0.4 x 10 has a major diameter of 5 mm.
A gauge number represents the fraction of an inch in diameter. To know the diameter, you need to refer to a gauge guide to match the gauge with a fraction of an inch. Lastly, you need to measure the distance from one thread to another. It’s also referred to as the pitch. In the metric system, we use pitch instead of thread spacing. To get this final measurement, use a ruler or measuring tape. In most cases, the pitch would only measure less than 1 mm. It is recorded in a decimal point of an mm. Generally, the metric system is easier to understand. It may take additional time to adjust if you are already comfortable with the imperial system. Instead of using gauges in expressing diameter, the metric system uses millimeters. On the other hand, it still uses millimeters to measure length.Fine-threaded screws are best used with pre-tapped holes. The closer distance between these threads allows a tight hold. However, it would take a longer time to remove or install. The third number is typically the one after the x, and it prescribes the length of the screw. You measure them all from the bottom of the head down to the tip. The only exception from the rule is flathead screws, which sit flush on the surface. You should measure this type from the top of the head down to the tip. An M5-0.4 x 15 has a length of 15 mm. Depending on the application, they come in different forms and sizes. Here are some of the most common ones. Cement Board
n. Some manufacturers offer non-standard pitches, so it is best to reach out to them for any concerns in customization. If the measurement reads M2 x 8, the diameter is 2mm and has a length of 8mm.
In the metric system, the threads are expressed in millimeters per thread. An M5-0.4 x 15 has a thread for every 0.4 mm. Screws are very versatile, making them a popular choice among people. The threads provide a sturdy grip, allowing them to meet the requirements of any project. They come in several types and sizes, which you can use in metal and wood. Other types are used for drywall and concrete. Screws are self-tapping, but you still have the option to drill a hole for it. Should you decide to go with the latter, it is less time-consuming to drill all holes first before installing the screws. Summary A concrete screw is what you need for fastening concrete. Some require you to pre-drill, while others are self-tapping. It allows you to drill directly into the surface without pre-drilling. Drive Types Structural wood screws have an unthreaded shaft and coarse threads. Structural wood ones may appear similar to wooden ones, but they are more durable. Sheet Metal
Sheet metal screws secure sheet metal. They are fully threaded and are available for use with self-drilling points and pre-drilled holes. Machine The gauge (imperial) is approximately the head’s size in millimeters (metric). However, there is no correlation or scientific explanation here. Metric System The first step in measuring the length is finding a surface to lay it down on an even surface. Start measuring wherever the head would rest when fully embedded into something. In some cases, you may need to hang it off the edge of a surface to lay it flat. Ones with a pan, round, or truss head should be measured from the bottom of the head to the tip. Ones with a flat or oval head should be measured from the top to the tip. Hex head ones are an exception to this rule, which means you need to measure from the bottom of the head. Brass, nylon, stainless steel, steel, aluminum, and titanium are a few of the materials used in fabricating this type. M4 screw sizeAn M4 screw is slightly larger than an M2. The M4 comes in several lengths but shares the same diameter of 4mm. The M4 screw size in inches is the equivalent of 0.15748. M5 screw size For the most accurate length, measure using millimeters from where the screw head sits to the tip. You don’t always measure from the top of the head. It depends on where the head would sit on the surface. Use a ruler or a measuring tape to get the most accurate measurement. Now that we have discussed some of the basics, it is time to guide you through what you need to know. Finding the right type and specifications will hold materials together nicely. Types When looking into and determining screw size dimensions, there are two things you need to understand – the length and the thread count. The latter is also commonly referred to as threads per inch (TPI) or thread pitch. We use the TPI to determine the thread’s fineness. The number will also tell if a screw can thread through a bolt. To measure screw size, we take its diameter. If the measurement says 1/4-20, it means it has a diameter of 1/4 inch and 20 threads per inch. A ruler is all you need to determine thread count and size.
Great Deal 
New Comment