Polyurethane sealants create an extremely strong mechanical bond when used on the correct surface. They are UV resistant and can be used below the waterline. In the aviation industry on unpressurized aircrafts, windows are sometimes attached using adhesive sealant only. This is a testament to the strength of modern sealants. It's notable that polyurethane is not compatible with acrylic perspex and other types plastic glazing. Elongation Break - Is the % of stretching that the product breaks at. Some sealants have been designed to stretch more than others. My next question is, can you reinforce that area underneath with support? It's about investigating why this has occurred. As that area will get heavy rainfall it needs to be well sealed. A favourite amongst boating enthusiasts CT1 is suitable as a universal adhesive and will work in all applications. CT1 has no shrinkage and can be applied in both damp and wet conditions. It adheres to most metals (including lead) as well as glass, mirrors, wood, polystyrene and GRP.

is all around one part polyurethane adhesive sealant that can be used to bond wood, gel coat and fibreglass. It can also be used above and below the waterline.Sealants were originally designed to patch holes in planes during the war but since then they've got a lot more complicated. Corporate competition means companies are continuously trying to outdo each other. The marine industry is constantly screaming out for products that last longer and perform better and subsequently, we are fed increasingly better sealants. A lot of companies who create sealants eventually wise up to the fact that their product will work in the 'marine' industry, and often subtly add it to their datasheet without it being a specific marine product and liable for leisure tax. Remove all of the sealant taking care not to damage the glass or frames, using a sharp knife. Tape the window and frames up using frog tape or blue painters tape then apply the sealant in even smooth beads. Paint types vary so conduct a trial prior to full application. Some paints have low movement and can Greg - I have a Meridian 391 2010 the front windows are leaking a little bit and is dripping in the master state room on the bed. I have tried to fill the area where the window sits on the lower side with silicon to achieve a water seal. Does not work. Pulled out all the silicon and I am going to try to fill and seal with Butyl or polyurethane. which would you recommend? A non-adhesive sealant will generally rely on the aid of a fitting, screw or bolt to create a waterproof seal. With a normal sealant, you are essentially creating a waterproof gasket. You can't rely on normal sealant to hold anything in place; you are relying on a method of fastening, for example; a screw or bolt. Types Of Sealant

I’m trying to visualise the issue, the swaging makes it a little more difficult. I’m not entirely, sure how any tube simply put through and hole will have a good seal. For a gasket to work you really need tension pushing outwards from the ID to seal. rubber changes over time, due to the elements and exposure. Tensile Strength - the resistance of a material to breaking under tension. To put it even clearer this is the amount of force a material can take until it breaks apart. This is measured in N/mm2 to MPa and can normally be found on a product datasheet. It looked great for a few weeks but then the planks dried and swelled etc and it popped the sealant. The sealant wasn't to blame here, the problem was there was a great deal of water getting in through the topsides of the boat. Delamination, leaky fittings and windows resulted in water pouring on the inside of the hull like a waterfall. As the boat was out of the water the planks were dry on the outside and taking a hammering of UV but wet on the inside. The new owner renewed the caulking, dropped it in the water and the problem seems to have been solved. I have since borrowed and cruised it and noticed no water ingress now that planks have swollen. Serviceability - how easily will I be able to remove and replace the sealant, how long does it take to set? Not resistant to organic acids, alcohol, concentrated mineral acids and caustic solutions or solvents.Before application, please ensure all surfaces are clean, dry and dust-free before using Everbuild Puraflex 40. All old sealant and mastic joints should be removed before application. In addition to that, when using on glass, metal and aluminium, areas should be cleaned using a solvent cleaner before application for optimum adhesion. When using with solvents, always ensure adequate ventilation. Avoid heat, sparks and open flames. Observe and follow all precautions listed on the solvent container label. It is not recommended for application to surfaces that are below 5˚C as it is impossible to guarantee a dry, frost-free surface at these temperatures. Therefore the sealant will most likely fail. It is unlikely that priming will be required; however, concrete must be sealed using a Primer. After that, if you are in doubt, consult Technical Services.

Specifically designed as an easy flow flooring grade for all concrete saw cuts and floor slab expansion joints where abrasion resistance is requiredEverbuild Stix-All is a one component adhesive sealant utilising the best elements of silicone and polyurethane technologies to create a hybrid. It hasn't been designed for marine use specifically but It is compatible for adhering with most the common materials and can be applied on both damp and wet surfaces. It will bond to metals, plastics, glass, concrete, plasterboard, plaster, polyester, perspex, glass, wood, enamel, painted surfaces and GRP.

Water - visibly dripping through into your cabin during rainy days. Leaking water can often be seen forming small droplets on the bottom of protruding bolt heads. Wait for a forecast of rain or cheat and use a hose to find leaks. If you get your bilge bone dry beforehand, you'll be able to follow the trails of water from any leaky hardware by looking at your bilge areas with a hand torch. This method works amazingly well. If you have a dirty bilge it seems to be even easier and the trail seems to show up clearer where the dirt is wet. Compatibility - will it work with your material you wish to bond it too? Will it be safe for below the waterline? We've even created a beautiful acronym for you to remember: 'SFCSS' (pronounced; Suu-Fuu-Cissss). See, if that's not catchy enough for you then I don't know what is! Terms Explained Hi Rich, If you are using aluminium frames then essentially the sealant will only need to be used to create a gasket. There is my opinion is no need to have a good adhesion if the window is held tight by rivets or bolts and a frame. Aquaseal mSEAL has been known to work well for this purpose and Geocel Marine Rubber Silicone is something I have personally used with good results.All surfaces must be dry and dust free before using Everbuild Puraflex 40. All flaking or loose surface coatings and any old sealants should be removed before application. In addition to that, when using on glass, metal and aluminium, areas should be cleaned with a proprietary solvent cleaner before application for optimum adhesion. When using Everbuild Puraflex 40 with solvents, always ensure adequate ventilation. Avoid heat, sparks and open flames. Observe and follow all precautions listed on the solvent container label. It is not recommended for application to surfaces that are below 5˚C as it is impossible to guarantee a dry, frost-free surface at these temperatures. Therefore the sealant will most likely fail. It is unlikely that priming will be required; however, concrete must be sealed using a Primer. After that, if you are in doubt, consult Technical Services. PRIMER There were posts about the "similarity" with CT1 and that it was actually an improved formulation. Also a threat of legal action plus mention in advertising that the OB1 formulation had been in use for over 15 years and made by a private company. I could not find details of the manufacturer and it almost seemed to be a big secret. It appeared reasonable to assume that some sort of legally binding agreement had been signed regarding direct competition or comparison with CT1 by name (could be wrong). is a one part polyurethane adhesive sealant which reacts chemically with water to deliver an extremely strong mechanical bond. Multiple sources including boat yard workers have claimed it's so strong its use as a marine sealant should be limited. It is apparently too strong for bedding equipment that may need replacing or maintaining in the future. However, It claims it is ideal for seals and joints both above and below the waterline. Debond by Marine Formula can be used to remove the sealant but be warned, it's expensive stuff! UniBond FlexTec FT101 is a one component hybrid polymer which can be used to seal, fill and bond. It claims to be able to bond without the use of a primer to a wide range of materials but doesn't specify which ones it does not. It can also be applied on both damp and wet surfaces but does take 24hours to set and may not ideal for fast same day repairs.