Joined in 2023 
82 
63 About this deal
Note that the Netgear Nighthawk X4S’s 2.4GHz band does display some issues towards the outer reaches of its range. Regardless of the device used, the router has a habit of disconnecting devices continually over 2.4GHz when the signal strength isn’t particularly strong. I’m sure that such issues are likely to be rectified with future firmware updates, but it makes switching from the Asus RT-AC68U unlikely. The odds are that your router isn’t supported if it isn’t listed here, but you could also try searching the DD-WRT wiki or simply Googling your router model number followed by “DD-WRT.” Note that “close enough” doesn’t work — you need the exact model number. Often, a different letter or number in a model name can signify an entirely different router. create /sys/devices/system/cpu/cpufreq/ondemand/sync_freq: Direwmi_unified_vdev_down_send for vap 0 (d6750000) With the R7800 Nighthawk X4S Smart WiFi Gaming Router, NETGEAR has produced its first all 4×4 AC2600 class router that, since it is Qualcomm-based, also has working MU-MIMO right from the start. Its top-of-line Broadcom-based R8500 Nighthawk X8 still has only a single beta release that supports MU-MIMO.
Wait about 4 minutes for the router to finish storing the firmware into its flash memory. When finished, the Power LED turns solid white and the wireless LEDs light up. To test 160 MHz mode operation, I asked NETGEAR to supply a device supporting 160 MHz mode. These are apparently hard to come by because NETGEAR shipped a second R7800 router and special firmware to make it operate as a 2×2 device. What most of us do is make a secure connection to our home network using VPN, via this secure connection you can connect to anything on your network including your USB storage of the router. sysinit: /etc/rc.common: eval: 1: cannot create /sys/devices/system/cpu/cpufreq/ondemand/optimal_freq: Directory nonexistenttem/cpu/cpufreq/ondemand/up_threshold_any_cpu_load: Directory nowmi_unified_vdev_down_send for vap 0 (d6750000) wifi0] FWLOG: [45466] vap-0 VDEV_MGR_VDEV_START ( 0x1685, sysinit: ath0: interface state UNINITIALIZED->ENABLED
Note that this recovery mode is in the bootloader (u-boot?), so it works before the actual firmware gets started. However, the premium paid won’t be worth it for many, especially given the connectivity issues I discovered when using 2.4GHz at long range. If you’re at the end of your tether with a bundled router, there are many cheaper options out there that will get you comparable results with today’s hardware in most houses. This is what I’ve added beyond turning on the majority of the dawn features (I don’t think the broadcast command does anything):Performance was solid on our 2.4GHz throughput tests. The R7800's score of 105Mbps on the close-proximity test was faster than the Asus RT-AC88U (97.9Mbps), the D-Link 890L/R (92.7Mbps), and the Linksys EA9200 (90Mbps). However, the R7800's score of 52.3Mbps on the 30-foot test trailed the Asus RT-AC88U (74.3Mbps) and the D-Link DIR-890L/R (82Mbps), and was nearly identical to the Linksys EA9200 (53.2Mbps). It gets a "high" rating of 8/10 and affects the D6220, D6400, D7000v2 and D8500 gateways and the R6220, R6250, R6260, R6400, R6400v2, R6700, R6700v2, R6700v3, R6800, R6900, R6900P, R6900v2, R7000, R7000P, R7100LG, R7300DST, R7800, R7900, R7900P, R8000, R8000P, R8300, R8500, R8900, R9000 and XR500 routers. I connected only one computer via Gigabit Ethernet at each end of the bridge. Baseline tests using Ethernet between the two computers show the Ethernet link capable of a bit over 940 Mbps in both directions with each direction run separately. So the hardwired part of the link shouldn’t be a limiting factor. The bridge R7800 reported a best case link rate of 1560 Mbps during this test. kwilt] start to get info from update-sever : https://http.fw.updates1.netgear.com/sw-apps/kwilt/r7800/
cpu cpu1: _opp_add: duplicate OPPs detected. Existing: freq: 600000000, volt: 900000, enabled: 1. New: freq: 600000000, volt: 900000, enabled: 1 cpu cpu0: _opp_add: duplicate OPPs detected. Existing: freq: 600000000, volt: 900000, enabled: 1. New: freq: 600000000, volt: 900000, enabled: 1Everything after Feb2016 is not in 4.4, about 10 commits in total. I looked at the commit list and one patch especially looks interesting as it promises to fix a major performance issue in dual-core processors (like ipq8065 in R7800). sysinit: WPA: Not enough entropy in random pool for secure operations - update keys later when the first station connects sysinit: Cannot connect to server , will try 60s later!!Configuration file: /var/run/hostapd-ath0.conf The following instructions assume that the research you did told you to flash the firmware using your router’s default upgrade tool. This is sometimes not the case, so make sure you’ve done your reading before continuing. Keep in mind that failing to do so may result in your router ceasing to function. You need TFTP flash once here, if you upgrade/downgrade from one group to the other group. Sysupgrade works normally inside each of those groups.
make defconfig" will expand the recipe to a full .config . You can run that command also manually.) In computer networking, the maximum transmission unit ( MTU) is the size of the largest protocol data unit (PDU) that can be communicated in a single network-layer transaction. The MTU relates to but is not identical to the maximum frame size that can be transported on the data link layer, e.g. Ethernet frame.ieee80211_ioctl_setparam-5962, IEEE80211_PARAM_NR_SHARE_RADIO_FLAG, MAX_RADIO_CNT = 2Saving Data... You might want to try to upload firmware to your router via TFTP if you are experiencing any of the following symptoms: This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. scripts/feeds update -a && ./scripts/feeds install -a && cp diffconfig .config && make defconfig && ./scripts/getver.sh
Great Deal 
New Comment