NOTES: All safety features were tested and certified at Sandia National Laboratories by Orion International Technologies Inc. All tests were done at ambient temperature, and all tests (apart from the lightning strikes) were repeated at 93°C - 121°C.​ Uses - Provides for safe operation of all Explosive Services including Perforating, Pipe Recovery, Setting

LCD colour display electric and diesel control panel allowing easy to use operation and easy visual indication of current conditions. Sensors and display: The pressure transducer is located on the switchgear and activates the pump start via the controller. The pressure gauge on the suction and pressure side (ø63mm) is located on the pump’s split housing. The input charge to the Firing Module must be between 32 and 40 volts. This low voltage input is applied to the input connector which charges a one microfarad capacitor. When this capacitor reaches 4000 volts, the Firing Module is ready to be fired. Triggering of the triggered spark gap occurs by applying a 30 volt pulse to the input connector. This discharges the one microfarad capacitor into the yellow terminals which, if properly connected, will fire the EBW detonator. Detonation will occur in less than 10 microseconds from the time that the 30 volt pulse is applied.

Within the UK, each building is defined by criteria of the installation and a relevant insurance body is appointed. If assigned to LPCB, then a hazard category would also be assigned. There are three of these - light hazard, ordinary hazard and high hazard and all are ranked depending on the combustibility rate of the items within the building (for instance, a high combustibility would be considered a ‘High Hazard’). Applications

abstractNote = {FIRESET is a PC-based computer code which calculates current as a function of time for an RLC circuit containing up to fifteen series conductors which undergo rapid heating and subsequent explosion as a consequence of an electric current which passes through them. In its original form, the code was developed to model electrical waveforms measured when a large, typically 25.4 x 25.4 x 0.051-mm, aluminum foil was exploded using a capacitor bank with tens of kilojoules of stored energy. The code proved to be useful for this purpose, and it was recognized that it could also be used for modeling the electrical response of detonator bridgewires. In view of the increasing use of slapper detonators for DOD applications, we wish to make the latest version of the code, available to DOD laboratories and contractors for use in designing firing systems which employ slapper or exploding bridgewire detonators. This document provides instructions for the code.}, Typically: large schools and offices, hospitals, hotels, restaurants, libraries, dairies, cement works, sheet metal producers and abattoirs. Please note an 8 hour double-walled fuel tank is as per the requirements in Factory Mutual Datasheets. Within NFPA20 a single-walled fuel tank sized to 5.07 litres per kW is acceptable, which is also available upon request. What standards is this equipment approved / compliant to? All components within the pumps are independently approved and tested ensuring the product meets the expected high quality. Standard-equipped with an air vent valve und pressure gauge installed directly on the main pump housingfrom 260kHz at 50V/m, electrostatic discharges, and severe direct lightning strikes to the wireline Radios stay on; communication links are unbroken; helicopter flights continue; construction work is uninterrupted; production is unaffected; the use of sensitive primary explosives is avoided. All of these advantages are available with the PX-1 fireset from Ecosse.

EBW and EFI detonators were originally developed for use in military applications. They need a very fast rising, high-current pulse for successful initiation, such as the output provided by the Ecosse PX-1. EFls are more difficult to initiate than EBWs, and they are typically 2-4 times more expensive. However, they use high-temperature explosives such as HNS, which means they can be used at higher temperatures than EBWs.fireset* To get the wand, the wand is used to select the area of the mission that will be created with the next command

Typical high hazard applications are storage and distribution facilities, areas where chemicals exist and high rise buildings over 45m. Benefits within 3ft of the PX-1 itself. Particularly on offshore platforms, these safety features can result Convenient & Cost Effective - The PX-1 EBW fireset allows normal oilfield operation to continue while

FM/UL fire set

Unlike conventional hot-wire and hot-resistor detonators normally used in oilfield perforating operations, EBW and EFI detonators do not contain sensitive primary explosives such as lead azide. LPS1239 1.1 – Requirements and testing procedures for the LPCB Approval and listing of diesel engines for sprinkler pump sets Tank: Fuel tank made from epoxy painted steel with a strong support structure. Fully equipped with a fuel gauge, drain plugs and air vent valves. The purpose of the FS-43 Control Unit is to provide low voltage electrical energy to the Firing Module and to ensure a safe and reliable operation sequence for the firing of EBW detonators.